Ebbe INNI 6100 Line Drain

Description

You can cut a single INNI to the desired length (between 73 3/4″ – 22″) on-site prior to installation. This gives you a precise, wall-to-wall drain channel that enables a single slope floor – ideal for large format tile.

Four ways to Install:

In-Sight Install: This installation places the Drain Channel away from the walls in your shower.
At-Wall Install: This installation places the Drain Channel flush against a tiled wall.
In-Shadow Wall Install: This installation places the Drain Channel under the wall tile. This is the least visible option.
In-Shadow Entry Install: This installation places the Drain Channel under the Shadow Curb at the entrance of your shower. Ebbe KERB – Shadow Curbs sold separately.

NOTE: The INNI Drain Body is made of ABS, glues directly to a 2″ waste pipe. PVC requires adaption via crossover cement or rubber coupling.

If you are doing a hot-mop installation, an INNI Hot Mop Receptor is required. (Sold Separately)

The INNI’s internal slope maintains water flow for a fresh, clean drain. Custom Brush Sets (sold separately) are easily able to clean all internal surfaces. Its access panel is smaller than your phone, for easy cleaning and waste pipe access.

Once you try the INNI, you’ll never go back!

Ebbe INNI connects directly to 2″ ABS pipe.

IMPORTANT: INNI is not approved to be installed outdoors due to freeze-thaw conditions. Also, INNI needs to be fully supported and is not approved to bridge gaps in the subfloor.

Tools and Supplies Needed for Install:

As a quick reference, here are the tools NOT included in the kit needed for installation:

At least 4 oz. ABS cement
Power Drill
Circular Saw, Miter Saw, Tile Saw
Urethane Sealant and Caulk Gun
Fiberglass Mesh Tape
Tape Measure
Utility Knife
Polymer Modified Thinset
Square
Spirit Level
Min. 3/8 x 3/8 Notched Trowel

Ebbe Shadow Trim (EILD-ST)

New anodized aluminum Trim for In-Shadow Wall install of your Ebbe INNI 6100 Line Drain!

Available in three finishes:

Ebbe Shadow Trim – Brushed Nickel

Ebbe Shadow Trim – Matte Black

Ebbe Shadow Trim – White

Each finish is available in four lengths to best suit your installation:

37.5in, 47in , 66in, or 75in

(All variations can be further cut to size on the jobsite)

Ebbe KERB – Shadow Curb (EK-SC)

Perfect for In-Shadow Entry install of your Ebbe INNI 6100 Line Drain!

The Shadow Curb is 1.1″ tall and is convenient for wheelchair access.

Available in four finishes:

Ebbe KERB – Shadow Curb – Brushed Nickel

Ebbe KERB – Shadow Curb – Matte Black

Ebbe KERB – Shadow Curb – White

Ebbe KERB – Shadow Curb – Polished Chrome

Each finish is available in four lengths to best suit your installation:

37.5in, 47in , 66in, or 75in

(All variations can be further cut to size on the jobsite)

Brush Set to clean INNI Line Drains (E6103)

The Brush Set is custom cut to the size of your installed INNI and is used to clean all internal surfaces of the drain body and slot with ease.

Brush Sets have been specifically designed to make maintenance of your INNI Line Drain effortless.

Through the access opening, a flexible stainless steel shaft with a D-shaped brush head cleans all interior surfaces with a simple push-pull motion.

Made of durable non-corrosive materials these cleaning brushes will give years of carefree service.

INNI Coupler Kit (E6106)

The INNI Drain Coupler Kit joins two INNI 6100 Line Drains together to create a drain channel longer than 73 3/4″.

Each INNI installed requires it’s own waste pipe connection.

INNI Drain Channel Slot Extender (E6105)

The INNI Drain Channel Slot Extender is used for At-Wall and In-Shadow installations to extend the drain channel.

Does NOT work for In-Sight installations.

Replacement Parts:

Angle Face Stainless Tile-In Access Cover for INNI 6100 (for 1/4in, 3/8in, or 1/2in thick tile)

The Angle Face Stainless Tile-In Access Cover comes with the INNI 6100 Line Drain and replacements can be purchased separately.

The Tile-In Access Cover matches the thickness of your tile and is used to cover/access the waste pipe below the INNI drain body.

Ebbe INNI Hair Trap (6-pack) (EILD-HT)

A single INNI Hair Trap comes with the INNI 6100 Line Drain and replacement Hair Traps are sold in packs of 6.

They are used to keep hair and debris out of your waste pipe for easy cleaning and maintenance.

In-Shadow Trim for INNI 6100 (1pc) (E6138-SH)

Two In-Shadow Trims come with the INNI 6100 Line Drain and replacement Trims are sold as a single 36″ piece.

This trim enables the In-Shadow installation of the INNI 6100 Line Drain, where the drain channel rests underneath the shadow of your wall tile.

In-Sight Angle Face Trim for INNI 6100 (1pc) (for 1/4in, 3/8in, or 1/2in thick tile)

Four In-Sight Angle Face Trims come with the INNI 6100 Line Drain and replacement Trims are sold as a single 36″ piece.

This trim creates a clean edge and finish within the drain channel.

End Sweeps for INNI 6100 (L&R w/ Top Decks)

End Sweeps are attached to both ends of the INNI 6100 Line Drain, closing the main drain channel so water will flow down the waste pipe.

Includes:
– Left End Sweep and Top Deck
– Right End Sweep and Top Deck

This is a replacement part. The INNI 6100 Line Drain includes both a Left and a Right End Sweep.

Ramps for INNI 6100

Ramps provide a smooth transition between the Main Drain Channel of the INNI 6100 Drain Body and the End Sweeps.

Includes:
– Ramps (A) (left and right)
– Ramps (B) (left and right)
– Ramps (C) (left and right)
– Ramps (D) (left and right)

On the under-side of the INNI 6100 Drain Body you will see zones marked A,B,C, D. Ramps are also marked A,B,C, or D. Choose the Ramp that matches the zone where the final cut has been made.

This is a replacement part. The INNI 6100 Line Drain includes each Ramp size.

View Ebbe INNI 6100 Line Drain Spec Sheet
View Ebbe INNI 6100 Line Drain Installation Instructions
ver desagüe de línea Ebbe INNI 6100 español Guía de instalación

Ebbe INNI 6100 Line Drain

Description

Ebbe Products

Cart